You may also like
Spec:
- Processor:STM32G071
- Firmware:BLHeli_32
- Working Voltage:2-8S Lipos (8.4V-33.6V)
- Continuous / Peak Current :70A / 150A
- PWM Frequency:16KHz-128KHz
- Input Set Support:Dshot 600/300/150, PWM, Oneshot, Multishot;
Telemetry Return :Support real-time data like motor RPM, temperature, current etc. available. - Galvanometer:Yes
- BEC :No
- Mounting Hole Spacing:20x20mm, Φ4mm/M3
- Product Size:50.5*36*6mm(L*W*H)
- Product Weight:15.8g
Features:
1)The esc is built with galvanometer supporting telemetry return, thus real time data like motor RPM, temperature, current etc. available.
2)High quality 8504mosfets with good heat dissipation and high efficiency conversion, which extending the flight time with long lifespan.
3)Multiple 8 layers PCB design with good heat dissipation and over-current capacity.
4)Excellent precise control of interval time switch enables high speed response and smooth control.
5)No worries of out-of-step problem with wide PWM frequency 16KHz-128KHz and excellent circuit design.
6)Compacted structure design with mounting holes suitable for easy mounting and suitable for various types of racks.
Spec:
- Model:63.0×L74.
- Shaft :Φ10
- KV: 140KV
- Volts: 8-16S
- Max Power: 3600Watts;Rated power:2400Watts.
- Max Current: 75 Amps;Rated current I/A:50Amps
- Insulation current AC500v/50Hz/1mA/3S
- Resistance R/mΩ :44.9
- Inductance L/uH 28.6
- Three-phase lead 3*12AWG (4.5mm)
- Plug: 4mm banana head (male)
- Internal structure :12N/14P
flipsky_esc_tool software and manual download link
Spec:
- Firmware: V1.3 or above (firmware update via Flipsky ESC Tool supported)
- Voltage: 14V-84V (safe for 4S-20S)
- Continuous current: 50V/550A; 75V/450A (Values depend on the mounting, ambient temperature
- and air/water circulation around the device!);
- Peak Current: 1000A
- BEC:5V@1A
- Motor/power Wire Size:8 AWG (3pcs combine)
- Programmable Tool: Flipsky ESC TOOL
- PWM Frequency Control: YES
- Multiple Speed Gear Limit Control:YES (UART / ADC)
- Regenerative Capacity: Yes
- Communication Ports: USB, CAN, UART, PPM, ADC
- Input Signal Support: PPM, ADC, UART (compatible with FLIPSKY remote VX4 and VX3Pro
- only at present, it will be compatible with more remote controllers soon)
- Startup Modes Support: IPDS (sensorless), HFPI (sensorless), HALL (sensored)
- Multiple Speed Gear levels: Low, Medium, High, Reverse
- Switch Support: Power on/off button switch or key switch
- Size: L227.5*W140*H54mm(with water cooling enclosure)
Features:
- Adopting CPU AT32F403ARCT7 with the structure of ARM Cortex-M4 allows CPU clock speed.
- 240MHz and the max PWM switching frequency 45KHz, which improves the motor RPM.
- Programmable via Flipsky ESC Tool to be compatible with multi-types of motor, different
- batteries voltages and many control ways.
- Programmable via Flipsky VX4 remote (Firmware Version:VX4_V1.2.1or above)
- Supporting FOC with low working noise and smooth starting.
- Supporting Real-time data and fault alerts.
- Supporting adaptive variable PWM frequency control.
- Supporting sensor mode(HALL) and sensorless modes (IPDS, HFPI).
- Supporting control types: Current, Duty Cycle.
- Protection functions: low and high voltage protection, motor over-temperature protection (suitable
- for NTC-10K-25℃ temperature sensing resistance only), battery over discharge protecting,
- mosfets over current and over-temperature protection.
Spec:
- Size: ∅ 65*150mm
- KV:160KV
- Voltage range: 4-13S
- Rated current: 30A;Maximum current:70A
- Insulation current:AC500v/1ma/3s
- Rated power:1500W;Maximum power:3000W
- Rated torque:2.3N.m;Maximum torque 4.5N.m
- Internal structure:12N/10p
- ESC drive mode:PPM
- Communication port: USB
- ESC driver firmware:5.2 vesc tool 3.00
- ESC support mode: BLDC/FOC
- Shaft specifications ∅ 12-0.005/-0.01
- Power cable: 2*12AWG(∅ 4.5mm*140)
- Power plug: XT90 male
- Weight:2.0kg
Spec:
- Model:FSESC 28120
- Processor:STM32G071
- Input voltage :DC 7V-33.6V(2-8S Lipos)
- Continuous current:120A
- Maximum current:150A
- Firmware:BLHeli_32 / AM32
- RGB LED Choices :Yes
- Cable Size:14AWG
- Programmable:Yes. Available for throttle calibration, timing angle setting, current detection, telemetry signal, motor rotation direction etc.
Spec:
- Model:FSESC 12100
- Processor:STM32G071
- Input voltage :18V-50.4V(5-12S Lipos)
- Continuous current:100A
- Maximum current:180A
- Firmware:BLHeli_32 / AM32
- BEC:NO
- Signal protocol:Dshot (All),PWM,Oneshot,Multishot,etc
- Programmable:Yes. (Available for throttle calibration, timing angle setting, current detection, telemetry signal, motor rotation direction etc.)
- RGB LED Choices:Yes
Product Description:
- Adopt 32-bit high-performance processor STM32G071 with working frequency 64MHz and maximum motor PWM frequency 128KHz .
- Adopt high-power MOSFETs and heatsink with good heat dissipation performance in high current.
- Support multiple motion modes such as uni-direction, bi-direction with braking etc.
- Support low voltage protection, temperature protection, locked rotor protection, current protection etc.
- The ESC automatically detects the throttle signal when it is powered on, supports all Dshot signals, and also supports signal protocols such as PWM, Oneshot and Multishot.
- Visual programming parameter adjustment tool supports motor timing, throttle calibration, current detection, motor steering, telemetry signal and other settings.
- Onboard RGB LED color light settings, multiple LED colors can be customized.
- Widely used in model airplane plant protection machines, multi-rotor drones, RC model ships and cars.